GermanLook Forums

GermanLook Forums (https://www.germanlook.net/forums/index.php)
-   Project Builds (https://www.germanlook.net/forums/forumdisplay.php?f=67)
-   -   Type IV Rocker Arms (https://www.germanlook.net/forums/showthread.php?t=11989)

effvee April 24th 2020 19:04

Type IV Rocker Arms
 
Hello everyone, with exception to Mr. Pauter, is there anyone else making type IV ration rocker arms?

Wally April 25th 2020 08:59

Quote:

Originally Posted by effvee (Post 92070)
Hello everyone, with exception to Mr. Pauter, is there anyone else making type IV ration rocker arms?

Yes, in germany there is a alu ratio rocker for sale now again. Think OK products make/sell it as well as Ahnendorp and a few others iirc. Not cheap.

effvee April 25th 2020 13:28

Thanks Walter.

Arnoud May 11th 2020 13:55

http://www.weiss-automotive-products.com/kipphebel.php

effvee May 11th 2020 16:08

1 Attachment(s)
Hello everyone,

Well it's good to see someone makes them. Question, have you seen the Pete Fusa rockers? I'm am not sure that they are for type IV heads though, I will send a e-mail and hope the answer is yes.

Wally May 12th 2020 05:16

Quote:

Originally Posted by effvee (Post 92108)
Hello everyone,

Well it's good to see someone makes them. Question, have you seen the Pete Fuser rockers? I'm am not sure that they are for type IV heads though, I will send a e-mail and hope the answer is yes.

I'am almost sure they're not, or otherwise they would have advertised so (its a bigger market then their full-race set-ups) and typ 4 rockers have a large off-set to one side per cylinder. Thats just eye balling it, but I think your hope is in vain, sorry.
Unfortunately, the Weiss rockers are very expensive (double what Pauters used to cost iirc, about 850-895 euro's?) and you need their billet valve cover since their rockers sit very high. Another 300-350? I think you might be well over 1200 euro's for just rockers and valve covers... I think Apfelbeck parts might not be that expensive after all LOL! :lmao:

effvee May 12th 2020 12:21

Good morning,
The rockers I showed were 1.7 ratio. I believe that they are not type IV also. I emailed him because, if a company can make that quality of a part, hearing his yes or no on possibly endeavoring to make some is worth at least asking the question.

1200 euros is high.

effvee May 14th 2020 17:48

Type IV rockers relpy
 
1 Attachment(s)
Hello everyone, please see the reply concerning the type IV rockers.

Hi there


On my website the rockers are typeV . It's not the same of pauter ok.

I already produced type 4 of pauter, I can do this without any problems.

I need a minimum order of 5 sets.

Value per sets of $ 650.00

Total $ 3,250.00

Question, is there enough members to place an order? I sent another picture of his rocker arms for him to validate. I also sent a picture of my engine, as the type IV, to make it clear. I believe Pauter started to have problems with reliability of his product. When I see Fusa product, it reeks quality. Because Brazil speaks Portuguese I am trying to make my point clear.

effvee May 18th 2020 17:30

Latest Reply On Fusa TypeIV Rocker Arms
 
1 Attachment(s)
Hello,
Presently I don't have the funds. However, just as soon as I am able I'll get some.

Wally May 19th 2020 14:29

Nah, I save my funds for OHC rockers and parts ;-)

effvee May 19th 2020 18:06

It's just a matter of time.
 
Quote:

Originally Posted by Wally (Post 92117)
Nah, I save my funds for OHC rockers and parts ;-)

Hello, not a problem, I'm very happy to see that there is someone that can and will make the rockers. I must stay on track now, I only need rockers and push rods. The Apfelbeck project has taken way too long, and I would have to go another route. I'll get my funds together and contact fusa then.

-Alex- October 24th 2020 11:33

I did design billet rockers once, i havent made them yet.

https://imagizer.imageshack.com/v2/1...924/K9hgBY.jpg


All times are GMT -4. The time now is 16:07.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved