GermanLook Forums  

Go Back   GermanLook Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.02 seconds.
Search: Posts Made By: Wally
Forum: Project Builds November 11th 2022, 14:23
Replies: 1,572
Views: 659,489
Posted By Wally
Haven't been here in a while, but for those still...

Haven't been here in a while, but for those still here: after the re-install of the whole turbo set-up, it made 475 hp at 1,6-ish bar boost on gasoline, 0% Ethanol, gas (the higher octane of course)...
Forum: Project Builds September 22nd 2020, 16:41
Replies: 1,572
Views: 659,489
Posted By Wally
Haha! Thanks man!

Haha! Thanks man!
Forum: Project Builds September 22nd 2020, 15:16
Replies: 1,572
Views: 659,489
Posted By Wally
Just a pic from early this year just out of...

Just a pic from early this year just out of hibernation ;-)

https://live.staticflickr.com/65535/50008490563_38967a2081_c.jpg
Forum: Project Builds May 2nd 2020, 07:17
Replies: 1,572
Views: 659,489
Posted By Wally
For those that don't do FB or STF, I got the...

For those that don't do FB or STF, I got the engine on the dyno yesterday and it did even better then I expected!

https://live.staticflickr.com/65535/49842259022_278559ce7b_b.jpg

244Nm @6K and...
Forum: Project Builds April 29th 2020, 09:52
Replies: 1,572
Views: 659,489
Posted By Wally
Its apperently an OEM oilcooler, but its from a...

Its apperently an OEM oilcooler, but its from a more obscure model (AMG?) Mercedes or so I understood. It has no part numbers, but I was looking for an upgraded one with the same M22x1,5 thread...
Forum: Project Builds April 25th 2020, 08:51
Replies: 1,572
Views: 659,489
Posted By Wally
As the car sits now (I just measured for you)...

As the car sits now (I just measured for you) almost 5 inches (12cm). Silencer is a little over 4 inches..
Forum: Project Builds April 24th 2020, 17:06
Replies: 1,572
Views: 659,489
Posted By Wally
Very positively as I have run them on the last 3...

Very positively as I have run them on the last 3 engines 😉
Forum: Project Builds April 24th 2020, 13:15
Replies: 1,572
Views: 659,489
Posted By Wally
Yes, big one, fits just behind front apron. ...

Yes, big one, fits just behind front apron.

Here is the old (small, old Mercedes transmission cooler) one and the current one:
https://live.staticflickr.com/65535/49745362721_1a1fbeaea6_b.jpg
Forum: Project Builds April 24th 2020, 13:14
Replies: 1,572
Views: 659,489
Posted By Wally
Of course! Today I had the two-yearly tech...

Of course!

Today I had the two-yearly tech inspection for road legality. Passed again :D

https://live.staticflickr.com/65535/49814163717_80171ff913_b.jpg

Had some small issue with a new...
Forum: Project Builds April 16th 2020, 04:09
Replies: 1,572
Views: 659,489
Posted By Wally
Its meant to become (work in progress) a 4-2-1...

Its meant to become (work in progress) a 4-2-1 header system with anti-reversion chambers build-in. Its also partially stepped :)
And it will be possible to retain my twin spark operation (the...
Forum: Project Builds April 15th 2020, 14:29
Replies: 1,572
Views: 659,489
Posted By Wally
https://live.staticflickr.com/65535/49769061093_c5...

https://live.staticflickr.com/65535/49769061093_c5fe94b8e1_b.jpg
Forum: Project Builds April 13th 2020, 03:28
Replies: 1,572
Views: 659,489
Posted By Wally
Yes, Deutz 102mm cylinders this time around, so I...

Yes, Deutz 102mm cylinders this time around, so I paid a little more attention to cooling as its not Biral material: bigger oil cooler and side scoops to ventilate the engine bay better when the...
Forum: Project Builds March 27th 2020, 08:46
Replies: 1,572
Views: 659,489
Posted By Wally
Alright, back to rebuilding this engine :D ...

Alright, back to rebuilding this engine :D

Mocking up for cam timing:
https://live.staticflickr.com/65535/49695111316_628fa09c50_b.jpg

Crank assembly untouched since emoved and will go right...
Forum: Project Builds January 21st 2020, 17:43
Replies: 1,572
Views: 659,489
Posted By Wally
404 and 414hp ;) Probably would have been...

404 and 414hp ;)

Probably would have been more if the ignition wasn't loosing power up top from a bad ground/earthing...
Forum: Project Builds January 21st 2020, 15:38
Replies: 1,572
Views: 659,489
Posted By Wally
Somehow its been too long since an update! And...

Somehow its been too long since an update! And this great forum can use a little more traffic I think.

The 102mm Deutz cylinders have been machined, new JE pistons with dish have arrived also and...
Forum: Project Builds August 13th 2019, 04:35
Replies: 1,572
Views: 659,489
Posted By Wally
Deutz is a tractor manufactorer and is always a...

Deutz is a tractor manufactorer and is always a diesel engine...The older jugs are better to use, but harder to find and as the word seems to be out about these (old autocrossers used these 25 years...
Forum: Project Builds August 4th 2019, 13:40
Replies: 1,572
Views: 659,489
Posted By Wally
Hey Simon, Thanks! And very good to hear...

Hey Simon,

Thanks! And very good to hear from you again! That has indeed been a looooong time!

I like the birals very much: in fact, I slao was a little worried about their thin-ish wall...
Forum: Project Builds June 16th 2019, 17:16
Replies: 1,572
Views: 659,489
Posted By Wally
https://www.youtube.com/watch?v=07wowurYL9M&featur...

https://www.youtube.com/watch?v=07wowurYL9M&feature=share
Forum: Project Builds June 15th 2019, 07:08
Replies: 1,572
Views: 659,489
Posted By Wally
It was weighed for inspection with the turbo...

It was weighed for inspection with the turbo engine and that was 960 kg about 12 years ago.
That was probably with half a tank and all seats in place.
Since then a few things are lighter, but added...
Forum: Project Builds June 14th 2019, 08:39
Replies: 1,572
Views: 659,489
Posted By Wally
https://live.staticflickr.com/65535/48060809836_01...

https://live.staticflickr.com/65535/48060809836_0136ae3429_b.jpg

First run 0,95-0,97 bar: 404 hp
last run 1,05-ish bar yielded 414 hp, so anyways it proved that you can make 400 hp on 1 bar on...
Forum: Project Builds June 14th 2019, 07:44
Replies: 1,572
Views: 659,489
Posted By Wally
Indeed mate! In fact, I had the car dyno’d...

Indeed mate!
In fact, I had the car dyno’d already at 1.0 bar boost...😎
Forum: Project Builds May 27th 2019, 03:30
Replies: 1,572
Views: 659,489
Posted By Wally
AN12 iirc, inside tunnel

AN12 iirc, inside tunnel
Forum: Project Builds May 26th 2019, 15:30
Replies: 1,572
Views: 659,489
Posted By Wally
Yep, since ~forever. Some people still think...

Yep, since ~forever. Some people still think thats a bad idea. Busted that myth long time ago. Its all about how you execute things.
Forum: Project Builds May 9th 2019, 14:38
Replies: 1,572
Views: 659,489
Posted By Wally
Engine long block is back in. Hydraulic clutch...

Engine long block is back in. Hydraulic clutch feels good again.

Test mounted intake (picture) to mark the spot where to install the waterinjection nozzle.
Since my old controller had a short and...
Forum: Project Builds May 4th 2019, 11:58
Replies: 1,572
Views: 659,489
Posted By Wally
Almost in again :) ...

Almost in again :)

https://live.staticflickr.com/65535/40806325243_5137dcd766_b.jpg
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -4. The time now is 09:32.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved