Forum: Project Builds
May 2nd 2013, 07:38
|
|
Replies: 155
Views: 118,777
Carter GP60504. You can get one from Summit. ...
Carter GP60504. You can get one from Summit.
Whatever spring you choose. Be sure to check for coil-bind when the valves are fully open. If the spring does not have some more room to compress when...
|
|
Forum: Project Builds
April 30th 2013, 04:41
|
|
Replies: 155
Views: 118,777
I used a section of pipe for the rocker shaft...
I used a section of pipe for the rocker shaft pivot. If you don't have any head leaks, no need to remove them. Use the tool to compress the springs. You can rotate the engine to almost TDC. Then...
|
|
Forum: Project Builds
April 29th 2013, 16:37
|
|
Replies: 155
Views: 118,777
Here you go. ...
Here you go.
http://i209.photobucket.com/albums/bb225/NO_H2O/DSCF0861.jpg~original (http://s209.photobucket.com/user/NO_H2O/media/DSCF0861.jpg.html)
|
|
Forum: Project Builds
April 27th 2013, 07:43
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
April 2nd 2013, 04:13
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
March 31st 2013, 08:43
|
|
Replies: 155
Views: 118,777
Autometer makes nice stuff. They have a good...
Autometer makes nice stuff. They have a good selection of senders except for CHT (the last time I looked). You can use a Westach CHT gauge and sender and paint the rim with aluminum paint and it will...
|
|
Forum: Project Builds
March 27th 2013, 19:42
|
|
Replies: 155
Views: 118,777
Good reading on oil....
Good reading on oil. http://http://www.lnengineering.com/oil.html
1200 ppm is a good guideline for the minimum ZDDP level to use in a flat tappet engine.
|
|
Forum: Project Builds
March 27th 2013, 04:17
|
|
Replies: 155
Views: 118,777
I would not replace the valve springs. You did...
I would not replace the valve springs. You did turn it a couple times a year. I would turn it over with the spark plugs out until you indicate oil pressure. Maybe repeat that a coupe times. Then...
|
|
Forum: Project Builds
March 22nd 2013, 07:34
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
November 14th 2012, 05:38
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
July 10th 2012, 10:50
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
July 5th 2012, 14:39
|
|
Replies: 155
Views: 118,777
Looks very nice. I would drop it onto a pan...
Looks very nice. I would drop it onto a pan secure all the parts with every other bolt so it does not get racked, use towels so the doors, hood, etc. don't rub, push it up on a trailer and drag it...
|
|
Forum: Project Builds
March 18th 2012, 09:59
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
March 17th 2012, 18:07
|
|
Replies: 155
Views: 118,777
Your tower looks fine. A FAT shroud does lot...
Your tower looks fine. A FAT shroud does lot require the machining that other 911 shrouds do. Zen went from a Fat 911 shroud to a DTM with no issues. Hell Jake's guys did it. No shims or machining...
|
|
Forum: Project Builds
March 16th 2012, 08:07
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
January 26th 2012, 14:30
|
|
Replies: 155
Views: 118,777
|
|
Forum: Project Builds
October 30th 2010, 06:50
|
|
Replies: 155
Views: 118,777
|
