GermanLook Forums  

Go Back   GermanLook Forums > General > Project Builds

Reply
 
Thread Tools Display Modes
  #151  
Old February 15th 2016, 00:20
owdlvr's Avatar
owdlvr owdlvr is offline
Administrator
 
Join Date: Sep 2008
Location: Canada - West Coast
Posts: 851
Saving me the trouble of reading back through your thread, are you able to answer any of the following:

1) Year of 901 transmission.
2) Model of Porsche the transmission came out of? (911, 912, etc)
3) Serial numbers and stampings on your transmission.
4) Photos of the following:
- Bellhousing, clutch fork and bearing installed.
- Bellhousing, clutch fork and bearing not installed.
- Clutch fork end, and your cable setup.
5) Part number on your clutch fork.

For now, before you pull the engine, reply with everything you're able to answer. Scour your photographs, and crawl under your trans for all the numbers and stampings. Basically, there are a number of different types of "901 transmission". There is the early aluminum case 901, there is the later magnesium cased 901 and then there is the 70-71 911 transmission which was based on the 901 but uses a pull-type clutch assembly. Basically, first step is sorting out which transmission you have. Then, the next is sorting out if that may have to do with your clutch issue.

HTH, or at least...hope it will!

-Dave
__________________
'71 Type 1 - Rally Project
'58 Type 1 - I bought an early!?!
'73 Type 1 - Proper Germanlook project
'68 Type 1 - Interm German 'look' project
'75 Type 1 - Family Heirloom
'93 Chevy 3500 pickup - Cummins Swap
Reply With Quote
  #152  
Old February 15th 2016, 04:21
spannermanager spannermanager is offline
Registered User
 
Join Date: Nov 2005
Location: London and kent.
Posts: 185
There is a given with grinding gear selection, the driven plate is exactly that, it's being driven, it's rotating with the fly when it should be ' released' and not free, so you can't get gears, two common reasons are the input shaft ' gland nut' or equivalent bearing are missing or failed leaving the shaft waggling in the breeze, or the driven plate is to thick, measure thickness against a known working plate, this one is very common.
Also Sometimes the input shaft is too long causing the same effect, it produces noise as described and grinding gears, it may be bottoming on the crank when the motor bolts are synched down, easy fix with a grinder.
Reply With Quote
  #153  
Old March 21st 2024, 19:08
Bugged Bugged is offline
Registered User
 
Join Date: Jan 2010
Location: Flagstaff, AZ
Posts: 126
Red face Better late than never?

Hey all, it's been awhile, but I've been slowly chipping away at the car pretty inconsistently. Quite a lot of updates to share. I finished painting the exterior, swapped out the fixed back seats (comfier for Dad), installed carpet, windows, and probably a bunch more I'm forgetting.

Paint: I actually paid someone locally to paint the remaining parts (Kerscher fenders, decklid, kamei spoiler, dash, etc). The sad part is that there was a paint mix up that was partially my fault and partially unprofessionalism. The paint ended up not matching and the painter basically wanted to charge me again, so I just did it myself.

Bad Paint



Here's some shots of me fixing the bad paint. Not only did it not match, but it had some significant pin holes and some terrible prep work (chipped fiberglass corners). This is only my second time really ever painting. I think it came out nicely, but feel free to give me some pointers.

First I figured out the issue with the paint. I had the painter use old paint and for some reason one can was not like the the others. I also was unable to match the existing paint by getting a new can of L96M mixed (even in the same brand).


Fixing pin holes


Primer and quick rinse


Smoothing out more crappy prep work


Rented a spray booth in town and got to business. Some of the parts had a lot of primer work to fix the mistakes so I first hit them with primer/surfacer (green). Then since I was still using the old paint I had, I sprayed the first base layer with a new can of L96M that doesn't match perfectly and followed with two layers of the old paint that matches.



Wear your safety equipment, auto paint is nasty. If I ever do it again or more often, I will definitely have a fresh air supply instead of an air filter. Google Isocyanates.



Little video link
https://photos.app.goo.gl/wu2eebEPb7CyEgU6A

First Coat




Clear Coat








Assembled Finally!
https://photos.app.goo.gl/2MBHYfkbgr56bbyC8









I will eventually fab up a bracket to mount an earlier style bumper instead of the bulky plastic 1974 fenders. If you look at the front bumper, I mounted an earlier style with the integrated turn signals.

Reply With Quote
  #154  
Old March 24th 2024, 03:48
Blizzard's Avatar
Blizzard Blizzard is offline
Registered User
 
Join Date: Apr 2009
Location: Groningen The Netherlands
Posts: 108
Your car and paint looks great. I have a sugestion what to use for the rear bumper. I would use a front bumper like you have in the front but without the integrated turn signals. A front bumper fits nicer with your wider Kerscher rear fenders.
Reply With Quote
  #155  
Old March 24th 2024, 17:42
Tomas Tomas is offline
Registered User
 
Join Date: Aug 2018
Posts: 9
Nice build! Where did you find that dashboard?
Reply With Quote
  #156  
Old March 25th 2024, 01:18
Bugged Bugged is offline
Registered User
 
Join Date: Jan 2010
Location: Flagstaff, AZ
Posts: 126
The front bumper is a good thought! I have an older model rear bumper but the radius seems to be a bit to tight and it sticks out a bunch.

The dashboard is from a fiberglass VW shop in Arizona by me called Glass Action.

https://glass-action.com/index.php/p...Dash-p57160526

Here's a pic of it in the car.



And the new seats! Corbeau with the VW plaid.

Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:20.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved