GermanLook Forums  

Go Back   GermanLook Forums > Technical Section > Brakes

Reply
 
Thread Tools Display Modes
  #1  
Old March 10th 2007, 05:05
pantswagen pantswagen is offline
Registered User
 
Join Date: Apr 2004
Location: london england
Posts: 154
71 bus spindles - turbo hub - boxster front caliper -996 front disc



-now the adaptor i need will need to be,
22mm and 17mm - ish

-ie a 89mm to aradial mount
caliper to spindle hole cetres = 25


spindle flats to caliper holes 17

-see its the hats of the 80mm 996 disc that make it all line up 'bob on'

-although, the caliper is suited to a 26mm disc, and the 996 is 28
-file the pins - scratch pack the pads


-hen when the discs wear, cut them , and fit new pads, gaining another bite of um cherry, ps - this wont work will drilled discs
Reply With Quote
  #2  
Old March 10th 2007, 05:11
pantswagen pantswagen is offline
Registered User
 
Join Date: Apr 2004
Location: london england
Posts: 154


-ie -easy adaptor!!
Reply With Quote
  #3  
Old March 10th 2007, 18:37
pantswagen pantswagen is offline
Registered User
 
Join Date: Apr 2004
Location: london england
Posts: 154
Reply With Quote
  #4  
Old March 13th 2007, 16:47
pantswagen pantswagen is offline
Registered User
 
Join Date: Apr 2004
Location: london england
Posts: 154
i have searched and searched

there is no magic bearing 19.050 - 50.005

or 31.075 - 60.005

but there are 19.050 - 53

and 31.075 to 62

so i shall be getting the hubs cut
-would have had to have done them anyway for the grease seal

-plus hopefully as the 19 - 53 is 22mm wide, i won't need to space them, as
the stock one is 13mm, and you need 8

-plus the rear one is a coule wider too

its good as the hub is stock to the spindle ish, not hanging out, like if i were to space it

75 quid for 4 bearings though!!!

21075 = 19.075 -53.975

15123 = 31.750 - 61.999

Reply With Quote
  #5  
Old March 15th 2007, 09:26
pantswagen pantswagen is offline
Registered User
 
Join Date: Apr 2004
Location: london england
Posts: 154
see a 09078 is 19.050 = 3/4 to 49.6

-you would have though they would have just make the farking bearing 50.005

-smokers of losenge shaped purple vein

similarily, with the stock type 2 bearing
31.750 -its 59.4

-you would have thought they would just have make the thing 60mm

1. 1/4 inch to 60mm

-when enquiring do you make such a bearing, you are greeted with
'are you from outer space'

farging farg

-end of moan, thats without asking, can you incorporate a 4mm spacer into each cup



-moan over

-so to fit a 951 hub onto a type 2 spindle -64 - 79, you need 3/4 to 50 19.050 too 50

inner is 31.750 = 1.1/4 to 60mm

-you need 4mm spacers under each cup

-some one do it!
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 15:09.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved