GermanLook Forums  

Go Back   GermanLook Forums > General > Project Builds

Reply
 
Thread Tools Display Modes
  #1  
Old October 1st 2010, 15:41
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
'56 rag with a twist

After lurking here for a while, time to post some pica's of my project.
I am not sure what it is exactly, is it german, resto, callook or race? you tell me


It all started in December 2007, after I sold my T2a single cab with 190Bhp G60 engine I bought this Oval. The plan was to use it as a daily and give it some TLC in de weekends.
This is how I bought it, original.

Planted a new gearbox and 2ltr type4 engine.

Narrowed, adjustable beem with dropped spindels.

And this is how I drove it (first time out was EBI II)


To make a long story short, it's a total resto now. The plan is to have the resto-cal ish look on the outside, with an inside, chassis and suspension that is ready for some strip and circuit aktion.

Let's start with the wheels;
I have two sets, fuch's and MAG industries, both with Porsche bolt patern.
One set for street use and one set for circuit/strip abuse.



Paul
__________________
If some is good and more is better, then too much should be just about right!

Last edited by fahrvergnugen; October 1st 2010 at 16:07.
Reply With Quote
  #2  
Old October 1st 2010, 15:44
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
The front suspension;

Porsche 914/911 with 944 hubs and disks.



Test fit.
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #3  
Old October 1st 2010, 15:45
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
Rear Suspension;
18cm narrowed to have the same width as an original oval.
IRS with 944 arms and brakes.

__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #4  
Old October 1st 2010, 15:46
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
Gearbox; 914 dogleg, raised with homemade mounting points.


__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #5  
Old October 1st 2010, 15:47
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
The "kill switch" I named it the "O ****" knob.

__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #6  
Old October 1st 2010, 15:48
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
Now I am working on the body.
Most of the rust on the right side is gone.

The complete doorpillar is gone.

And replaced.



And today I was working on the 1/4 panel.
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #7  
Old October 1st 2010, 15:50
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
Almost ready, after using some lead filler it looks like new again 8)
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #8  
Old October 1st 2010, 15:55
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
For an oval they even don't sell the bad fitting repro sheet metal. The only thing I could do is restore the old metal.
Together with some Tikimadness leftovers :thumbsup: (drag race oval) I will try to fix it again.



With these 2 holes the body is mounted to the torsion tube. My torsion tube is about 9cm narrowed (each side) so these holes needs to be moved.





Here's the difference;
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #9  
Old October 1st 2010, 15:58
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
The original form was long gone, so I had downloaded some pictures and started moddeling metal.



It's a corner you can't see when the car is ready, but I like it to look original.
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #10  
Old October 1st 2010, 15:59
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
Finally finished the left corner. When the body is back on the channels I will cut the corners at the wright lenght.



Nice fit, only have to grind the welds down and use some lead to smooth things.



On to the right site.
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #11  
Old October 1st 2010, 16:53
fahrvergnugen fahrvergnugen is offline
Registered User
 
Join Date: Jun 2009
Location: The Netherlands
Posts: 285
Found some pics of the custom rear suspension;






Paul
__________________
If some is good and more is better, then too much should be just about right!
Reply With Quote
  #12  
Old October 1st 2010, 20:07
Xellex's Avatar
Xellex Xellex is offline
Registered User
 
Join Date: Sep 2007
Location: Bucharest, Romania
Posts: 274
daaamn! nice project! I always said the Netherland and especially Keversite.nl has the most GL projects going on. Too bad of the language barrier, so thanks for posting here, in english! I often read through the Keversite forums with the help of google translate :P
__________________
www.vw1303s.com
Reply With Quote
  #13  
Old October 1st 2010, 20:17
volkdent's Avatar
volkdent volkdent is offline
Moderator
 
Join Date: Oct 2002
Location: Santa Rosa, CA, USA
Posts: 1,685
Oh man, you are up to your eyeballs with that project!!! Great work, can't wait to follow the progress.

You and Ricola need to get together and have a beer discussing how many Km of welding wire you used on your projects!!!

Jason
__________________
If I could just get paid for my sleepless nights....
1960 VW Bug UBRDUB
Walkaround
1st Drag Run

Dyno Run
Oval Ragster-'57 Rag/'04 Boxster S
Reply With Quote
  #14  
Old October 2nd 2010, 04:24
Fast65 Fast65 is offline
Registered User
 
Join Date: Sep 2010
Posts: 30
looks great loving the front suspension

cheers andy
Reply With Quote
  #15  
Old October 2nd 2010, 04:37
ricola's Avatar
ricola ricola is offline
Registered User
 
Join Date: Jul 2002
Location: Warwick, UK
Posts: 1,137
Good to see you have made progress since I last looked at your main thread! One thing I'm not sure about is the inner bit of your spherical bearing mount. It looks like you have a rigid outer (hole in steel plate) and a urethane surrounded inner mount, this will lead to movement and potential fatigue in the bolt. I think if you just made the inner part rigid it would be good (much better than a lot of other kits that use loose outer plates...
Rich
__________________
http://www.ricola.co.uk
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 23:26.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved