GermanLook Forums  

Go Back   GermanLook Forums > General > Project Builds

Reply
 
Thread Tools Display Modes
  #1  
Old April 24th 2020, 19:04
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Type IV Rocker Arms

Hello everyone, with exception to Mr. Pauter, is there anyone else making type IV ration rocker arms?
Reply With Quote
  #2  
Old April 25th 2020, 08:59
Wally's Avatar
Wally Wally is offline
Registered User
 
Join Date: Nov 2002
Location: The Netherlands
Posts: 2,552
Quote:
Originally Posted by effvee View Post
Hello everyone, with exception to Mr. Pauter, is there anyone else making type IV ration rocker arms?
Yes, in germany there is a alu ratio rocker for sale now again. Think OK products make/sell it as well as Ahnendorp and a few others iirc. Not cheap.
Reply With Quote
  #3  
Old April 25th 2020, 13:28
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Thanks Walter.
Reply With Quote
  #4  
Old May 11th 2020, 13:55
Arnoud's Avatar
Arnoud Arnoud is offline
Registered User
 
Join Date: Oct 2008
Location: The Lowlands
Posts: 30
http://www.weiss-automotive-products.com/kipphebel.php
__________________
pre-'55 oval:stuffed in a barn
1972 1302S(Cali Type4 EFI)
1973 1303S(soon with Oettinger TSV2000)
Reply With Quote
  #5  
Old May 11th 2020, 16:08
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Hello everyone,

Well it's good to see someone makes them. Question, have you seen the Pete Fusa rockers? I'm am not sure that they are for type IV heads though, I will send a e-mail and hope the answer is yes.
Attached Images
File Type: jpg Rockers.jpg (58.3 KB, 22 views)
Reply With Quote
  #6  
Old May 12th 2020, 05:16
Wally's Avatar
Wally Wally is offline
Registered User
 
Join Date: Nov 2002
Location: The Netherlands
Posts: 2,552
Quote:
Originally Posted by effvee View Post
Hello everyone,

Well it's good to see someone makes them. Question, have you seen the Pete Fuser rockers? I'm am not sure that they are for type IV heads though, I will send a e-mail and hope the answer is yes.
I'am almost sure they're not, or otherwise they would have advertised so (its a bigger market then their full-race set-ups) and typ 4 rockers have a large off-set to one side per cylinder. Thats just eye balling it, but I think your hope is in vain, sorry.
Unfortunately, the Weiss rockers are very expensive (double what Pauters used to cost iirc, about 850-895 euro's?) and you need their billet valve cover since their rockers sit very high. Another 300-350? I think you might be well over 1200 euro's for just rockers and valve covers... I think Apfelbeck parts might not be that expensive after all LOL!
Reply With Quote
  #7  
Old May 12th 2020, 12:21
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Good morning,
The rockers I showed were 1.7 ratio. I believe that they are not type IV also. I emailed him because, if a company can make that quality of a part, hearing his yes or no on possibly endeavoring to make some is worth at least asking the question.

1200 euros is high.

Last edited by effvee; May 12th 2020 at 17:25.
Reply With Quote
  #8  
Old May 14th 2020, 17:48
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Type IV rockers relpy

Hello everyone, please see the reply concerning the type IV rockers.

Hi there


On my website the rockers are typeV . It's not the same of pauter ok.

I already produced type 4 of pauter, I can do this without any problems.

I need a minimum order of 5 sets.

Value per sets of $ 650.00

Total $ 3,250.00

Question, is there enough members to place an order? I sent another picture of his rocker arms for him to validate. I also sent a picture of my engine, as the type IV, to make it clear. I believe Pauter started to have problems with reliability of his product. When I see Fusa product, it reeks quality. Because Brazil speaks Portuguese I am trying to make my point clear.
Attached Images
File Type: jpg 20171202_133814.jpg (50.5 KB, 26 views)
Reply With Quote
  #9  
Old May 18th 2020, 17:30
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Latest Reply On Fusa TypeIV Rocker Arms

Hello,
Presently I don't have the funds. However, just as soon as I am able I'll get some.
Attached Images
File Type: jpg 20170920_143026.jpg (87.4 KB, 16 views)
Reply With Quote
  #10  
Old May 19th 2020, 14:29
Wally's Avatar
Wally Wally is offline
Registered User
 
Join Date: Nov 2002
Location: The Netherlands
Posts: 2,552
Nah, I save my funds for OHC rockers and parts ;-)
Reply With Quote
  #11  
Old May 19th 2020, 18:06
effvee effvee is offline
Registered User
 
Join Date: Aug 2002
Location: California
Posts: 701
Smile It's just a matter of time.

Quote:
Originally Posted by Wally View Post
Nah, I save my funds for OHC rockers and parts ;-)
Hello, not a problem, I'm very happy to see that there is someone that can and will make the rockers. I must stay on track now, I only need rockers and push rods. The Apfelbeck project has taken way too long, and I would have to go another route. I'll get my funds together and contact fusa then.
Reply With Quote
  #12  
Old October 24th 2020, 11:33
-Alex- -Alex- is offline
Registered User
 
Join Date: Oct 2009
Location: Finland
Posts: 278
I did design billet rockers once, i havent made them yet.

Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:48.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved