Forum: Suspension
February 12th 2010, 13:47
|
Replies: 28
Views: 8,379
|
Forum: Suspension
October 29th 2006, 17:30
|
Replies: 46
Views: 59,221
|
Forum: Suspension
September 29th 2006, 19:10
|
Replies: 46
Views: 59,221
|
Forum: Wanted
September 29th 2006, 13:50
|
Replies: 2
Views: 2,812
|
Forum: Suspension
September 28th 2006, 21:05
|
Replies: 7
Views: 2,920
|
Forum: Suspension
September 28th 2006, 16:44
|
Replies: 7
Views: 2,920
|
Forum: Suspension
September 28th 2006, 06:45
|
Replies: 7
Views: 2,920
Your shimmie is a rarer one!
Check all of...
Your shimmie is a rarer one!
Check all of the above as well as the joints in the steering. Pay particular attention to the idler bushings and steering box.
It appears there is no single...
|
Forum: Suspension
September 22nd 2006, 05:05
|
Replies: 46
Views: 59,221
|
Forum: Brakes
September 20th 2006, 11:12
|
Replies: 8
Views: 5,371
|
Forum: Engines
September 20th 2006, 04:12
|
Replies: 10
Views: 3,061
|
Forum: Engines
September 20th 2006, 04:04
|
Replies: 10
Views: 3,061
|
Forum: Engines
September 19th 2006, 05:58
|
Replies: 10
Views: 3,061
|
Forum: VolkSport Käfer Gruppe
September 17th 2006, 18:57
|
Replies: 39
Views: 8,856
|
Forum: Suspension
September 17th 2006, 17:44
|
Replies: 46
Views: 59,221
Good call Wally.
Remove the passenger side...
Good call Wally.
Remove the passenger side mounting bracket from the housing by removing the M8 nut and bolt. Next is the second hard part..
Remove the ring-clip from the end of the housing,...
|
Forum: Wheels
September 17th 2006, 05:50
|
Replies: 11
Views: 5,225
215/40 and 215/45 on 7.5et52mm under Day...
215/40 and 215/45 on 7.5et52mm under Day Mouldings. Probably the absolute limit, the front is tight with a wheel alignment for cornering such as 2deg -ve camber. Inner sidewall is ~4mm from a 80mm...
|
Forum: Suspension
September 16th 2006, 18:17
|
Replies: 46
Views: 59,221
First time I looked, I didn't see how it came...
First time I looked, I didn't see how it came apart either ;)
I pulled my rack apart (2 actually) last week.. It can be stripped down to every last part. I scored new pinion roller bearings, the...
|
Forum: Suspension
August 7th 2006, 13:50
|
Replies: 4
Views: 2,307
|
Forum: Suspension
July 28th 2006, 20:12
|
Replies: 21
Views: 6,205
Hi Paul, I assumed the hubs were the same, they...
Hi Paul, I assumed the hubs were the same, they look it :eek: Like I said the hubnut's are still on my Ali arms, on the shelf for nearly 4 years.. I would have them on the car if Day Moulding wings...
|
Forum: Suspension
July 15th 2006, 19:32
|
Replies: 41
Views: 11,097
Very nice arms. I like how the old boss bears...
Very nice arms. I like how the old boss bears load.
Just to make a point about the Red9 kit mentioned earlier, the bars that pass through the torsion housing each have a bearing at each end.
...
|
Forum: Suspension
July 15th 2006, 18:58
|
Replies: 1
Views: 2,157
Hi, Welcome!
The 924 doesn't really have...
Hi, Welcome!
The 924 doesn't really have much to offer you, really. The strut housing is a late 1303 part, the stub-axle may have the positive camber problem same as 944, I haven't tried it...
|
Forum: Suspension
July 15th 2006, 18:17
|
Replies: 6
Views: 2,045
I have this down to a fine art. We have a...
I have this down to a fine art. We have a 10,000kgf press and access to a 100t, this is a better method sometimes when the part is awkward or lacking in meat to press against, like T1 and T2...
|
Forum: Suspension
July 15th 2006, 17:39
|
Replies: 5
Views: 2,560
|
Forum: Suspension
February 6th 2006, 16:09
|
Replies: 86
Views: 19,878
IRS camber adjustment is made simple by...
IRS camber adjustment is made simple by installing the Kerscher rear anti-roll bar bolts.
A spanner (open ended wrench) is used on a hex bolt to make the adjustment.
I can't find a picture of...
|
Forum: Transmissions
January 26th 2006, 14:28
|
Replies: 17
Views: 4,679
|
Forum: Transmissions
January 25th 2006, 19:19
|
Replies: 3
Views: 3,847
|