Forum: Project Builds
May 9th 2012, 02:32
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
May 7th 2012, 17:11
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
May 7th 2012, 05:07
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
March 5th 2012, 18:11
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
January 25th 2012, 08:50
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
January 3rd 2012, 18:54
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
March 11th 2011, 13:59
|
Replies: 1,572
Views: 777,969
Thanks for that!
A friend is switching from...
Thanks for that!
A friend is switching from an E48 to a S60 on his turbo bug and is currently using TPS and were weren't sure whether to switch to MAP as load instead of TPS. We will stay with TPS
|
Forum: Project Builds
March 11th 2011, 10:56
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
December 28th 2010, 07:23
|
Replies: 1,572
Views: 777,969
Nice one Wally! Did you put rope inside the...
Nice one Wally! Did you put rope inside the cylinder to hold the valve or did you use air pressure?
Great idea with the jubilee clips, that would made it much easier for me if I had thought of...
|
Forum: Project Builds
November 27th 2010, 11:50
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
November 27th 2010, 10:16
|
Replies: 1,572
Views: 777,969
I bet that was quite daunting chopping of the...
I bet that was quite daunting chopping of the collector - the point of no return!
Could you do me a favour please - measure the ID of the single pipe coming from the collector. I need to order a...
|
Forum: Engines
November 27th 2010, 05:15
|
Replies: 24
Views: 7,770
I have the same dipstick and tube. Its an...
I have the same dipstick and tube. Its an aftermarket small block chevy one. The tube needs curving around, and then the case drilling to accept the larger diameter tube compared to the stock one....
|
Forum: Project Builds
July 10th 2010, 12:53
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
July 2nd 2010, 07:25
|
Replies: 1,572
Views: 777,969
|
Forum: Engines
April 19th 2010, 18:05
|
Replies: 6
Views: 2,563
|
Forum: Project Builds
March 6th 2010, 12:40
|
Replies: 1,572
Views: 777,969
|
Forum: Project Builds
March 5th 2010, 08:57
|
Replies: 1,572
Views: 777,969
HI Wally,
I think you misunderstand me a...
HI Wally,
I think you misunderstand me a little.
You only run this test once, and this is only to tell you how the boost rises against RPM.
At 4000rpm you can easily attain 1.6 bar, but at...
|
Forum: Project Builds
March 4th 2010, 14:53
|
Replies: 1,572
Views: 777,969
I have a theory about how to setup these boost...
I have a theory about how to setup these boost maps on the DTA that we are going to try on my friends beetle when he has it running again.
You really need a dyno to set it up, and a ignition cut...
|
Forum: Suspension
July 11th 2005, 17:24
|
Replies: 7
Views: 2,232
|
Forum: German Look Tuning
July 11th 2005, 17:19
|
Replies: 3
Views: 1,836
|
Forum: Brakes
January 4th 2005, 21:23
|
Replies: 159
Views: 136,215
You remembered it the wrong way round!
A...
You remembered it the wrong way round!
A drum mc has a residual pressure valve in, of around 10psi, this prevents the springs on the shoes retracting the wheel cylinders all the way in.
On a...
|
Forum: German Look Tuning
December 22nd 2004, 11:34
|
Replies: 19
Views: 9,454
You tried Rallydesign?
...
You tried Rallydesign?
http://www.rallydesign.co.uk
They are very cheap for Oil coolers (in fact cheaper than Thinkautomotive who actually make them and sell them to rallydesign)
Paul
|
Forum: Engines
May 15th 2004, 13:18
|
Replies: 8
Views: 3,292
|
Forum: Suspension
May 14th 2004, 19:40
|
Replies: 12
Views: 4,015
Oh if you are not running 944 rear then its not...
Oh if you are not running 944 rear then its not too bad, very low though and they are too long and the CVs will get knocked out quickly, as will the grease seals on the output flanges from the box,...
|
Forum: Suspension
May 14th 2004, 13:28
|
Replies: 12
Views: 4,015
|