Engine combo... need some advice please

[NO_H2O]

I have a budget beater T1 engine going together right now. Most of the parts are used but not very much. I got a set of old school Cima 94 p/c's, oil pump, solid shaft rockers push rod tubes and 6 cut push rods(clue #1), 2 Scat cams and a good AH case (stock) from a friend for $200 all where very lightly used. Also scored a pair of lightly used S/E heads (big valves) for $275 and a full 45 Dellorto set-up(dual) with rebuild kits at a swap meet for $200, 1 3/4 merged S&S with a ceramic coated MangaFlow fat boy $200, Mallory dist. for $30, traded for a new Kennedy press plate and disc, etc, etc. I have bought a new cam and lifters(Web Cam) and will have about $1000 in a 2275. I have just taken my time and collected stuff as I find it.

[vujade]

Originally Posted by NO_H2O

I have a budget beater T1 engine going together right now. Most of the parts are used but not very much. I got a set of old school Cima 94 p/c's, oil pump, solid shaft rockers push rod tubes and 6 cut push rods(clue #1), 2 Scat cams and a good AH case (stock) from a friend for $200 all where very lightly used. Also scored a pair of lightly used S/E heads (big valves) for $275 and a full 45 Dellorto set-up(dual) with rebuild kits at a swap meet for $200, 1 3/4 merged S&S with a ceramic coated MangaFlow fat boy $200, Mallory dist. for $30, traded for a new Kennedy press plate and disc, etc, etc. I have bought a new cam and lifters(Web Cam) and will have about $1000 in a 2275. I have just taken my time and collected stuff as I find it.

you da' man Dave

[super vw]

Do delloroto 40mm DRLA carbs bolt right up to Wber IDF maifolds, and use the same hex linkage?

That set of dells on ebay for under 200 sounds like my ticket if i can use weber maifolds and linkage.

Later
Jonathan

[volksdragon]

as far as i know they do. and that guy is also offering those carbs pre jetted for you. man i'd swap my spare shot block for a pair of those.

[craazy Cooter]

Originally Posted by super vw

Do delloroto 40mm DRLA carbs bolt right up to Wber IDF maifolds, and use the same hex linkage?

That set of dells on ebay for under 200 sounds like my ticket if i can use weber maifolds and linkage.

Later
Jonathan

Dude is that ebay guy the alfa71 or whatever? if so Make the buy now! He kicks ***. I got carbs from him. Thyere the cool euro models with the cable pull enrichment circuits. I bought a weber linkage kit from ebay for $100 and it was basically everything but the carbs. I used a weber 40mm kit for my dellorto 36mms. it works perfect. no problems with dell compatibility whatsoever.

[super vw]

Originally Posted by craazy Cooter

Dude is that ebay guy the alfa71 or whatever? if so Make the buy now! He kicks ***. I got carbs from him. Thyere the cool euro models with the cable pull enrichment circuits. I bought a weber linkage kit from ebay for $100 and it was basically everything but the carbs. I used a weber 40mm kit for my dellorto 36mms. it works perfect. no problems with dell compatibility whatsoever.

YES! SO... so are his carbs clean?

[craazy Cooter]

Yup! no corrosion or anything . they run so smooth with such good response its amazing. Get two gasket kits too. he sells them also. he's like the dellorto god of europe or something. I even used the gaskets that came with em. they looked like 10,000 mile carbs.

[boygenius]

Originally Posted by craazy Cooter

Yup! no corrosion or anything . they run so smooth with such good response its amazing. Get two gasket kits too. he sells them also. he's like the dellorto god of europe or something. I even used the gaskets that came with em. they looked like 10,000 mile carbs.

Does he always have carbs for sale. I'm not ready for carburetors yet.
But I don't want to miss a good thing.