915 output flanges vs. 944 cv joints

[LOAF]

BG,

Question for you.. FYI, I have been cross posting.. but I am lost...

See if you can help me out here.. As far as a conversion with the following.. 901 (911) tranny to 944 late N/A arms.. what do I need once I have everything on the ground..

As I mentioned my not so unique situation is the following..

I am doing the 944 late conversion with sigle piston brakes.. I have the following parts that I would like to reuse as part of this conversion..

The have the 944 Stub axles.. which I am not sure I can swap out..
The 944 Axle that is conected to the Stub..
and shortly within a week a 901 (911) tranny...901 trans from a 66-68 912/911

The seller has different output flanges, but for starters I am not sure which flanges to even ask for.. man I am confused..

I am not sure what can mate with what.. If there is a simple solution out there.. I am not looking at Big Hp numbers.. 100-150 at most..

What is your recommendation?

As far as the tranny T2, or is there a stock 901 part?

Which axles. 944 or T2.. will these mate to the 944 stub axle.. I will check how many splines and if it has a part number..

What CV Joints do I use?

Do I have to replace the 944 Stub axle?

Help
Alex

[Michael Ghia]

Alex,
If you want to use 944 arms, no matter which arms they are (steel, narrow ally or wide ally) then use the driveshafts complete with CV joints which come with them.
In order to marry those driveshafts up to the 901 tranny, you will need output flanges from a 911SC 915 tranny.

The early 901 comes with small (T1 size) output flanges and the late 901 comes with 930 size output flanges. The 914 box comes with T1 size output flanges.

Another way to make stuff work would be to use the early or 914 output flanges (T1 size) and swap the CV joints over on the end of the driveshafts with T1 CV joints... that said I have never tried this so you'll be the guineapig! I suspect that the splines on the shaft will be the same but that you'll have to use an extra spacer on the splines before you put the cv joint on as the T1 CV joints are narrower than the Porsche ones.

Good luck, if I lost you please say so and I'll try to explain again.

Mike

[LOAF]

MG,

The first part makes sense, a little lost on second half..

As fas as sourcing 911SC 915 Flanges.. Is this a hard thing to come across..

I will do some investigating.. but for now this seems like my best choices..

Thanks again Michael.

ALex

[LOAF]

Michael,

I just got done with an email and got asked about the SC flanges..

The Sc Flages came two way corse spline and fine spline. Which do I need?

Thanks
Alex

[boygenius]

Alex, I'm not a real transmission expert so I can't be of any real help. The early and late aluminum trailing arms use the same axles and are interchangable. As long as they are 33 spline the type 1 CV joints will fit them, That is what Zen is using on his car right now. You should just be able to bolt up the axles using the type 1 inner CV's like Micheal Ghia suggested if you can't get the drive flanges you want.

[trevorbrady]

Originally Posted by boygenius

The early and late aluminum trailing arms use the same axles and are interchangable.

BG, is this a FACT, or second hand information? I don't mean to doubt you, but I want to be 110% sure!
I need to get drive shafts for my project pretty soon (i'm making do with type1 shafts and CVs as the type1 arms are still in place at the moment), and I need to know EXACTLY which ones, as mistakes in buying Porsche parts are costly mistakes!

I have early aluminium arms. I thought I needed early-late (make sense?) drive shafts to suit, but the early aluminium arms were only in production for a short while and are rarer compared to the late-late arms. If I knew for a fact that late-late drive shafts would do, I could get them pretty easily.

Just a thought, but how do type 2 drive shafts measure up, length-wise, against the various type1/924/944 drive shafts?
I know blind chicken has a page with comparisons between shafts/cvs, but I don't remember them comparing overall lengths of shafts. Anyone ever definitively document the differences in lengths?

[zen]

early and late arms both use 21" axles. i had a set of early arms on my bug first and then switched to late. there is a thread on here somewhere with good detail and pics as i was going through it. the difference in the width between the arms occurs at the hub. compare a rotor for a early and late and you will see what i mean. in fact, there is also a pic somewhere on here where i stacked the two arms and took some pics.