|
|
#106
June 15th 2011, 14:54
|
|||
|
|||
|
Time to take out the old grinder again
 . I really need the parts for my oval, but still it was difficult to cut up this nice '58.No way back now.    Paul.
__________________
If some is good and more is better, then too much should be just about right! 
|
|
#107
June 19th 2011, 14:45
|
|||
|
|||
|
After a lot of drilling, the dash is out.
   Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#109
July 6th 2011, 06:18
|
|||
|
|||
|
Quote:
I am very buisy wright now drilling all the spotweld of the donor car, no pictures yet. Als had a very cool weekend at EBI #4. Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#110
July 9th 2011, 16:33
|
|||
|
|||
|
The EBI Chimay weekend was superb, but now it is oval time again.
Al the old repairs are cut out of the donor front and today I started cleaning the underside of it. This is a very good piece of German metal.    Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#111
July 16th 2011, 10:07
|
|||
|
|||
|
Finally did something visible again.
Complete parafan removed.  Took a wile to find the currage, but it had to be done.  Both doorpillars removed :shock: :shock:   Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#112
July 20th 2011, 15:14
|
|||
|
|||
|
a few holes.
Looked at an original , never welded body and then circled all the original holes. The rest has to be welded.  How it should be.  After storage for many years, this all original (only the exhaust cutouts are not original), rust free and never welded oval is my workshop neighbor. now i can check it if I need to know how things should be. (i am not aloud to touch it ;D)  Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#113
August 27th 2011, 16:09
|
|||
|
|||
|
Replaced the right windshield heater thing and repaired the left one.
  In the past someone drilled a lot of holes in this car, today I fixed it. This is a difficult to reach area, so while I was in there I might as well bare metal it.   Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#114
August 28th 2011, 13:08
|
||||
|
||||
|
nice
|
|
#115
September 7th 2011, 15:37
|
|||
|
|||
|
Getting close 8)
  Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#116
September 8th 2011, 11:48
|
||||
|
||||
|
My hat is off to you. Lots of metal work going into this one.
__________________
NO_H2O 72 1302 Smack Black GL 73 Bus (2L CIS Powered) 66 Beetle, 73 Standard Beetle 72 Pinzgauer 710M Volksport Kafer Gruppe
|
|
#118
September 8th 2011, 14:19
|
|||
|
|||
|
Thanks Guys,
I am not afraid of doing new things. this kind of work is new for me, but i'll get there. Paul
__________________
If some is good and more is better, then too much should be just about right!
|
|
#119
September 11th 2011, 13:59
|
|||
|
|||
|
Satrting to look good.
 Right side is getting there as well.  Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
|
#120
November 30th 2011, 17:14
|
|||
|
|||
|
Between family live, work and some work on my daily passat, the oval is going forward as well (slowly).
Bolted the nose on the body, now i can see better what to do and where to do it. It looks like the right is OK.   On the left I had some fitting problems, probably the welds from the pedalbox where to hot. I cut out the piece that did not fit and welded in a bigger piece instead.   Still needs some welding, grinding and sanding. Paul.
__________________
If some is good and more is better, then too much should be just about right!
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
