Imohr from Brazil

[owdlvr]

Thank you for posting these!

And after going through your photos, I now understand what some of my friends who had seen them in person were talking about:







Here's the thing, those welds aren't necessarily "bad", but I would be tempted to sandblast the parts to confirm them. I talked it over with a fabricating buddy of mine when I was considering ordering the full front/rear setup (before I bought the red car) and we agreed that we can't reverse engineer the setup for less than they are charging. Even if we have to re-make a couple of their parts, we are far better off both economically and time wise.

-Dave

[effvee]

Originally Posted by owdlvr

Thank you for posting these!

And after going through your photos, I now understand what some of my friends who had seen them in person were talking about:







Here's the thing, those welds aren't necessarily "bad", but I would be tempted to sandblast the parts to confirm them. I talked it over with a fabricating buddy of mine when I was considering ordering the full front/rear setup (before I bought the red car) and we agreed that we can't reverse engineer the setup for less than they are charging. Even if we have to re-make a couple of their parts, we are far better off both economically and time wise.

-Dave

Wow, suspension is one thing, but steering is another. If you question the quality of workmanship, are you going to put your health and wellbeing on the line? Is there a reason why you don't reach out to the builder with your concerns, maybe ask for the questionable part be replaced. You may need pay for shipping, better than a hospital stay

[owdlvr]

Originally Posted by effvee

Wow, suspension is one thing, but steering is another. If you question the quality of workmanship, are you going to put your health and wellbeing on the line? Is there a reason why you don't reach out to the builder with your concerns, maybe ask for the questionable part be replaced. You may need pay for shipping, better than a hospital stay

Well, it's not my kit, but my comments on someone else's kit. I would still be fine purchasing the kit, knowing I may need to make some corrections. For myself, I have more confidence that we (being my motorsport fabrication friends and I) can correct/repair any issues faster and with more confidence then I would have with "sending it back" for fixes.

When you do the math on the time and effort to develop something like this, it's often much faster to improve upon a design already made.

[effvee]

Originally Posted by owdlvr

Well, it's not my kit, but my comments on someone else's kit. I would still be fine purchasing the kit, knowing I may need to make some corrections. For myself, I have more confidence that we (being my motorsport fabrication friends and I) can correct/repair any issues faster and with more confidence then I would have with "sending it back" for fixes.

When you do the math on the time and effort to develop something like this, it's often much faster to improve upon a design already made.

Understood, however if something goes wrong, the buyer assumes the responsibility..

[owdlvr]

Originally Posted by effvee

Understood, however if something goes wrong, the buyer assumes the responsibility..

You're buying a major suspension/steering component from Brazil...that completely alters the vehicle from stock. You are absolutely taking on all the responsibility, whether you alter it or not.

[jmd]

I totally agree and was willing to take the risk - I wont run it if I'm not absolutely confident in the parts. I've chatted with the Imohr crew and they back their work 100% - I'm having them inspected by a structural welder and engineer for safety. Further, if they are found wanting, I will just have them 'rewelded". The remainder of the parts and the quality overall is well worth it.

Appreciate the community looking out for each other!
Remember guys, safety 3rd!
heh.

[wouter1303]

Originally Posted by owdlvr

Thank you for posting these!

And after going through your photos, I now understand what some of my friends who had seen them in person were talking about:

.....

Here's the thing, those welds aren't necessarily "bad", but I would be tempted to sandblast the parts to confirm them. I talked it over with a fabricating buddy of mine when I was considering ordering the full front/rear setup (before I bought the red car) and we agreed that we can't reverse engineer the setup for less than they are charging. Even if we have to re-make a couple of their parts, we are far better off both economically and time wise.

-Dave

Those welds look kinda 'big', doesn't mean they're bad indeed. But I have seen different...
And since suspension is something you have to trust....
This will keep me thinking what to buy in the furure.
I once saw someone make these in aluminium, but i can't find it.