Forum: Engines
April 9th 2013, 22:47
|
|
Replies: 27
Views: 22,268
|
|
Forum: Project Builds
April 9th 2013, 21:54
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
April 7th 2013, 02:16
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
April 3rd 2013, 02:42
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
April 2nd 2013, 16:55
|
|
Replies: 155
Views: 226,395
I am pretty sure I will get these seats, Sparco...
I am pretty sure I will get these seats, Sparco Sprint 5. They are narrow enough to fit in the bug without looking awkward in my opinion. FIA approved and have the submarine hole for the 5th belt....
|
|
Forum: Project Builds
April 2nd 2013, 16:53
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
April 1st 2013, 22:22
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
March 31st 2013, 14:14
|
|
Replies: 155
Views: 226,395
Do I need to run a CHT on each cylinder? If I...
Do I need to run a CHT on each cylinder? If I just wanted to run a dual CHT gauge, which cylinders would I put the sensors on? Was it Cylinder #3 that runs the hottest? Should I put the sensors on...
|
|
Forum: Project Builds
March 31st 2013, 01:05
|
|
Replies: 155
Views: 226,395
|
|
Forum: Engines
March 30th 2013, 02:37
|
|
Replies: 27
Views: 22,268
|
|
Forum: Project Builds
March 29th 2013, 02:47
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
March 27th 2013, 10:39
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
March 27th 2013, 01:58
|
|
Replies: 155
Views: 226,395
Also, my motor was built, bench dyno'd and...
Also, my motor was built, bench dyno'd and initial break in, and then it sat in an airconditioned garage for 15 years. It was turned over a couple times a year. It was recommended to me that I...
|
|
Forum: Engines
March 27th 2013, 01:37
|
|
Replies: 27
Views: 22,268
|
|
Forum: Project Builds
March 27th 2013, 01:17
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
March 21st 2013, 01:28
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
March 20th 2013, 23:22
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
March 20th 2013, 13:40
|
|
Replies: 155
Views: 226,395
All 4 fenders with shipping was about 1100 US...
All 4 fenders with shipping was about 1100 US dollars. Then they get you at customs again. Unless you have a import broker who will do it for free. Tack on about another 300-400 dollars to get...
|
|
Forum: Project Builds
March 17th 2013, 21:47
|
|
Replies: 155
Views: 226,395
I'm rebuilding my 944 cv joints. Is the...
I'm rebuilding my 944 cv joints. Is the orientation of the inner race to the outer race directional? I the inner race has some wear on one side so I flipped it around so the balls will rest on the...
|
|
Forum: Suspension
January 25th 2013, 01:44
|
|
Replies: 14
Views: 21,061
Nice! Good work, I need to take a look at my...
Nice! Good work, I need to take a look at my set-up once I am road worthy... What is the disadvantage of simply using the "Flip it bump steer" bushings? I've put a link below. Do these not have...
|
|
Forum: Suspension
January 20th 2013, 02:01
|
|
Replies: 14
Views: 21,061
I agree making the control arm and tie rod...
I agree making the control arm and tie rod parallel significantly reduces the delta between control arm and tie rod left/right position. The fact that the two are different lengths ultimately makes...
|
|
Forum: Body
January 15th 2013, 01:32
|
|
Replies: 4
Views: 2,867
Woah!! That is a lot! In that case, I don't...
Woah!! That is a lot! In that case, I don't think you will fit under 6cm fenders. You may be able to fit under the 7cm depending on your tire choice/stretch. I'm going to say that you will be...
|
|
Forum: Body
January 13th 2013, 02:59
|
|
Replies: 4
Views: 2,867
|
|
Forum: Project Builds
January 4th 2013, 14:33
|
|
Replies: 155
Views: 226,395
|
|
Forum: Project Builds
January 4th 2013, 08:47
|
|
Replies: 155
Views: 226,395
|
